Bunk Bed Disposal

Guide · Homeowners · 3 min read · Updated 16 November 2026

How to Dismantle a Bunk Bed Safely: Step-by-Step Guide

Short answer

To dismantle a bunk bed, strip the bedding and mattresses, remove the ladder and guard rails, take out the top bunk slats, then separate the top bunk from the bottom bunk by lifting it off its connecting dowels or undoing the joining bolts. Finally, unbolt the side rails from the end frames. Always work with two people, and remove any wall brackets first.

A room with bunk beds

Before you start

Bunk beds are tall and top-heavy once the mattresses are off, and the top bunk can be awkward to lift down. Most need two adults to dismantle safely. Allow 30 to 60 minutes for a standard bunk, and longer for a high sleeper with a desk or storage. Keep children and pets out of the room while you work, because panels can fall and small fixings are a choking hazard.

Find the assembly instructions if you still have them, as they show the order of fixings. If not, work from the top down and keep each set of bolts in a labelled bag.

  • Allen keys in common sizes and a set of spanners
  • Cross-head and flat-head screwdrivers
  • A rubber mallet for stubborn dowel joints
  • Small bags and a marker for fixings
  • Blankets or towels to protect floors and walls
  • Penetrating oil for rusted bolts on metal frames

Step by step for a standard bunk bed

Strip the bedding and lift both mattresses out. Check whether the bed is fixed to the wall with a bracket or strap. Remove that first, because the bed may move once you start loosening it. Then work through the stages below, keeping the bed stable at all times.

StepWhat to doWatch out for
1. Wall fixingUndo any brackets or anti-tip strapsBed may shift once released
2. LadderUnbolt or unhook the ladderSome ladders bolt into the side rail
3. Guard railsRemove the top bunk safety railsKeep fixings separate and labelled
4. Top slatsLift out or unroll the top slatsSlats may be screwed or clipped
5. Separate bunksLift the top bunk off its dowels or undo joining boltsTwo people needed to lift
6. FramesUnbolt side rails from end framesSupport panels as bolts come out

Separating the top and bottom bunks

Many wooden bunk beds are two single beds stacked on dowels or connecting pins. Once the ladder, guard rails and slats are off, two people lift the top bunk straight up off the dowels, one at each end, and lower it to the floor. If it sticks, a gentle tap upwards with a rubber mallet usually frees it. Never stand on the bottom bunk to lift the top one, because the bed can rock.

Metal bunks often join with long bolts through the corner posts. Support the top bunk before removing the last bolts so it does not drop. On some metal designs, the posts are one piece from floor to top, in which case the side rails come off first and the end frames are lowered whole.

High sleepers and cabin beds

High sleepers and mid sleepers are usually fixed to the wall to stop them tipping, and they have more panels than a standard bunk. Remove the desk, shelves and any wardrobe or cupboard units first, as they often brace the frame. Then take off the ladder and guard rails, lift out the slats and work down the frame. Keep a hand on the structure as you go.

Cabin beds come apart more like a chest of drawers. Pull out the drawers and trundle, remove the doors, then undo the cam locks and screws that hold the panels together. Chipboard panels are easily damaged, so lay them flat rather than leaning them against walls.

Dealing with stuck or rusted fixings

Metal bunks used in hostels, campsites and staff blocks often have bolts that have rusted solid. Spray them with penetrating oil and leave it for ten minutes before trying again. Use a spanner or socket that fits snugly to avoid rounding off the bolt head. If a bolt will not move, it may need cutting with a hacksaw or an angle grinder, which is a job for someone experienced.

On wooden beds, stripped Allen bolts and spinning barrel nuts are common. Holding the barrel nut still with a flat screwdriver while turning the bolt usually solves it.

Protecting the room

Panels and frames are long and easy to swing into walls, windows and light fittings. Lay blankets on the floor before you start, and lower parts slowly rather than letting them fall. Watch the ceiling light when lifting the top bunk. Once the wall bracket is off, the screw holes will need filling and touching up if you want the wall to look tidy.

Carry parts out in order, starting with the smallest. Long side rails are easiest carried vertically on stairs, with one person at each end.

If you would rather not do it yourself

Dismantling is included in every bunk bed collection. A standard frame costs from £45 to dismantle and remove, a bunk with two mattresses costs £65–£90 and a high sleeper with a desk or wardrobe costs £70–£110. The team brings the tools, protects the room and takes everything to the correct recycling routes.

If you have already dismantled the bed, leave the parts near the door with the fixings bagged and mention it when booking. If you started and got stuck, for example on a seized bolt or a wall bracket you cannot reach, that is fine too. Tell us how far you got and the team will finish the job, taking any loose panels and fixings with them so nothing is left behind in the room.

Questions people also ask

Can one person dismantle a bunk bed?

It is not recommended. Lifting the top bunk off its dowels, supporting frames as bolts come out and handling long side rails all need two people. Working alone risks the bed tipping or a panel falling, which can injure you or damage the room. Ask for help, or book a team to do it.

What tools do I need to take a bunk bed apart?

Usually a set of Allen keys, a set of spanners or sockets, cross-head and flat-head screwdrivers and a rubber mallet. Penetrating oil helps with rusted metal frames. Have small bags ready so fixings do not get lost, especially if you plan to sell or reuse the bed.

How do I separate a bunk bed into two single beds?

Many wooden bunks can be separated into two singles. Remove the ladder, guard rails and top slats, then lift the top bunk off its connecting dowels with a second person. Some models need the dowels replaced with end caps or short feet to stand as a single bed. Check the manufacturer's instructions.

Written and checked by the Bunk Bed Disposal team. Read our editorial policy.

Get a free bunk bed disposal quote

Tell us what you need and we'll come back with a clear price.

Request a quote